Reset your Holosun EPS Carry Red Dot Sight

Occasionally, you may need to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected performance. Fortunately, resetting your Holosun is a straightforward process that can be achieved in just a few procedures.

First ensuring your red dot sight is powered on.
Locate the small reinitialize button on the side of the sight.
Utilize a thin tool to press and hold the reset button for approximately 5 seconds.
Release the switch and your Holosun EPS Carry Red Dot sight will reboot.
The red dot sight should now be set back to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it back to standard configuration is a breeze. First, locate the tiny button on the side of your optic. Then, press and hold it for around twelve seconds until you see a brief flash. Your Holosun EPS Carry is now reverted to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

Press and hold the power button for approximately 5 seconds.
A message will flash, indicating that the reset is successfuly initiated.
Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and confirm your sight's functionality. If you encounter any further difficulties, don't hesitate to reach out to their technical assistance.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

First, Activate your Holosun EPS Carry by pressing the power button.
Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
As you continue holding these buttons, tap the power button once.
You will show a confirmation prompt indicating that the reset process is initiated.
Allow the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reset your Holosun EPS Carry through a Factory Standard Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the solution. This will restore your sight to its website factory settings, clearing any personalized configurations you've made. To execute this reset, observe these easy steps:

To begin, find the reset button on your EPS Carry.
Secondly, engage a thin object, like a pen tip, to activate the reset lever.
During keep the reset switch engaged, power on your EPS Carry.
You'll flash a message showing that the reset is finished.

Once the reset is complete, your EPS Carry will be back to its factory settings.